driver

Getting ATI cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the radeon or the proprietary fglrx driver with your ATI graphics card to make sure your card is functioning as it should.
 
Note: As of November 2008, the ATI drivers still do support kernel 2.6.27 and Xorg 7.4, however X seems to crash when starting. Until the drivers functions correctly with Fedora 10, they will not be available from the RPM Fusion repositories.

Getting ATI cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

  • Yum configured to use the 3rd party RPM Fusion repository
  • If building the drivers using the packages directly from ATI/AMD's site, please install a few packages first:
    su -c 'yum install qt-devel compat-libstdc++-33 -y' 

 

The 'radeon' driver

Radeon is an open-source alternative to the proprietary fglrx driver, offering support for many (but not all) ATI cards including some that aren't supported any longer in the latest fglrx drivers! While it's performance may not match exactly that of fglrx, its performance is still very decent. It is included in part of the standard Xorg driver packages in Fedora, so it requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "radeon"

Once you restart the computer everything should be functioning.

Please remember that if you previously were using another driver, you may need to use the livna-config-display tool to switch back to the 'AIGLX' configuration:

livna-config-display --tui -a

 

The 'fglrx' driver

To install the fglrx driver, simply run the following commands:
su -
yum install kmod-fglrx xorg-x11-drv-fglrx
fglrx-config-display enable
service fglrx restart

Please note that for a xen kernel, 'kmod-fglrx-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-fglrx-PAE) and so on. Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-fglrx-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "ATI Technologies" and not "Mesa".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the ATI/AMD website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option "VideoOverlay" "On"
Q: Does fglrx 8.52.2 (aka Catalyst 8.11) really work with Xorg 7.4?
A: Although reports say it does (on Ubuntu Intrepid, Gentoo and OpenSuSE for example), the driver does not function correctly with Fedora at the moment.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting nVidia cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the nv, nouveau or proprietary nvidia driver with your nVidia graphics card to make sure your card is functioning as it should.

Getting nVidia cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

The 'nv' or 'nouveau' driver

The nv and nouveau drivers are the open-source alternatives to the proprietary nvidia driver, offering support for many of the nVidia cards. The downside to the nv driver is that unlike the open source 'radeon' driver for ATI cards, it does not support direct rendering, also called DRI or hardware-accelerated rendering. The nouveau project, however, aims to fix this by developing a new free driver with working DRI for nVidia cards. Currently, it is (as the name goes ;) ) a new project and it's not ready for everyday use quite yet.
 
Either way, both of these drivers are included in part of the standard Xorg driver packages in Fedora, so they requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "Name"

Where 'Name' is either 'nv' (recommended) or 'nouveau' if you're feeling lucky. Once you restart the computer everything should be functioning (or maybe not if you chose the 'nouveau' driver)

 

The 'nvidia' driver

A note on legacy drivers:

Please note that any card below and including the GeForce FX series is no longer supported by the mainstream nvidia drivers.

If you have a Riva or TNT card, you are going to have to use the nvidia legacy drivers. Simply follow the instructions below like normal but replace all instances of:

  • kmod-nvidia with kmod-nvidia-legacy
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-legacy
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-legacy-libs.i386
  • service nvidia [action] with service nvidia-legacy [action]

If you are using a GeForce2, 3 or 4 (including MX) card, a you are going to have to use the 96xx series. Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-96xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-96xx
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-96xx-libs.i386
  • service nvidia [action] with service nvidia-96xx [action]

If you are using a GeForce FX (5xxx) card, a you are going to have to use the 173xx series. Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-173xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-173xx
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-173xx-libs.i386
  • service nvidia [action] with service nvidia-173xx [action]
 
To install the nvidia driver, simply run the following commands:
su -
yum install kmod-nvidia xorg-x11-drv-nvidia
nvidia-config-display enable
service nvidia restart

Please note that for a xen kernel, 'kmod-nvidia-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-nvidia-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-nvidia-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "NVIDIA Corporation" along with your card name and version - NOT "Mesa Indirect".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the nVidia website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option      "AddARGBGLXVisuals" "True"
Q: How come I can't use Beryl or Compiz?
A: Please take a look at your xorg.conf and remove the 'Module' section if you have it. Xorg can autoconfigure and guess at a lot of things and even run without a xorg.conf (but that's not recommended). Without a Module section, you're sure that Xorg will load all the modules you need where as with one it will only load what is specified, not more.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting ATI cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the radeon or the proprietary fglrx driver with your ATI graphics card to make sure your card is functioning as it should.
 
Note: As of November 2008, the ATI drivers still do support kernel 2.6.27 and Xorg 7.4, however X seems to crash when starting. Until the drivers functions correctly with Fedora 9, they will not be available from the RPM Fusion repositories.

Getting ATI cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

  • Yum configured to use the 3rd party RPM Fusion repository
  • If building the drivers using the packages directly from ATI/AMD's site, please install a few packages first:
    su -c 'yum install qt-devel compat-libstdc++-33 -y' 

 

The 'radeon' driver

Radeon is an open-source alternative to the proprietary fglrx driver, offering support for many (but not all) ATI cards including some that aren't supported any longer in the latest fglrx drivers! While it's performance may not match exactly that of fglrx, its performance is still very decent. It is included in part of the standard Xorg driver packages in Fedora, so it requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "radeon"

Once you restart the computer everything should be functioning.

Please remember that if you previously were using another driver, you may need to use the livna-config-display tool to switch back to the 'AIGLX' configuration:

livna-config-display --tui -a

 

The 'fglrx' driver

To install the fglrx driver, simply run the following commands:
su -
yum install kmod-fglrx xorg-x11-drv-fglrx
fglrx-config-display enable
service fglrx restart

Please note that for a xen kernel, 'kmod-fglrx-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-fglrx-PAE) and so on. Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-fglrx-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "ATI Technologies" and not "Mesa".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the ATI/AMD website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option "VideoOverlay" "On"
Q: Does fglrx 8.52.2 (aka Catalyst 8.11) really work with Xorg 7.4?
A: Although reports say it does (on Ubuntu Intrepid, Gentoo and OpenSuSE for example), the driver does not function correctly with Fedora at the moment.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting nVidia cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the nv, nouveau or proprietary nvidia driver with your nVidia graphics card to make sure your card is functioning as it should.

Getting nVidia cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

The 'nv' or 'nouveau' driver

The nv and nouveau drivers are the open-source alternatives to the proprietary nvidia driver, offering support for many of the nVidia cards. The downside to the nv driver is that unlike the open source 'radeon' driver for ATI cards, it does not support direct rendering, also called DRI or hardware-accelerated rendering. The nouveau project, however, aims to fix this by developing a new free driver with working DRI for nVidia cards. Currently, it is (as the name goes ;) ) a new project and it's not ready for everyday use quite yet.
 
Either way, both of these drivers are included in part of the standard Xorg driver packages in Fedora, so they requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "Name"

Where 'Name' is either 'nv' (recommended) or 'nouveau' if you're feeling lucky. Once you restart the computer everything should be functioning (or maybe not if you chose the 'nouveau' driver)

 

The 'nvidia' driver

A note on legacy drivers:

Please note that any card below the GeForce FX series is no longer supported by the mainstream nvidia drivers.

If you have a Riva or TNT card, you are going to have to use the nvidia legacy drivers. Simply follow the instructions below like normal but replace all instances of:

  • kmod-nvidia with kmod-nvidia-legacy
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-legacy
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-legacy-libs.i386
  • service nvidia [action] with service nvidia-legacy [action]

If you are using a GeForce2, 3 or 4 (including MX) card, a you are going to have to use the 96xx series. Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-96xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-96xx
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-96xx-libs.i386
  • service nvidia [action] with service nvidia-96xx [action]
Please note that the 177.82 driver dropped support for GeForce FX (5xxx) cards. Because of this, the main driver package for Fedora 9 at RPM Fusion will not be updated to 177.82. Instead, please install the newest series package to obtain the 177.82 drivers by replacing:
  • kmod-nvidia with kmod-nvidia-newest
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-newest
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-newest-libs.i386
  • service nvidia [action] with service nvidia-newest [action]
 
To install the nvidia driver, simply run the following commands:
su -
yum install kmod-nvidia xorg-x11-drv-nvidia
nvidia-config-display enable
service nvidia restart

Please note that for a xen kernel, 'kmod-nvidia-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-nvidia-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-nvidia-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "NVIDIA Corporation" along with your card name and version - NOT "Mesa Indirect".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the nVidia website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option      "AddARGBGLXVisuals" "True"
Q: How come I can't use Beryl or Compiz?
A: Please take a look at your xorg.conf and remove the 'Module' section if you have it. Xorg can autoconfigure and guess at a lot of things and even run without a xorg.conf (but that's not recommended). Without a Module section, you're sure that Xorg will load all the modules you need where as with one it will only load what is specified, not more.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting ATI cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the radeon or the proprietary fglrx driver with your ATI graphics card to make sure your card is functioning as it should.

Getting ATI cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

  • Yum configured to use the 3rd party RPM Fusion repository
  • If building the drivers using the packages directly from ATI/AMD's site, please install a few packages first:
    su -c 'yum install qt-devel compat-libstdc++-33 -y' 

 

The 'radeon' driver

Radeon is an open-source alternative to the proprietary fglrx driver, offering support for many (but not all) ATI cards including some that aren't supported any longer in the latest fglrx drivers! While it's performance may not match exactly that of fglrx, its performance is still very decent. It is included in part of the standard Xorg driver packages in Fedora, so it requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "radeon"

Once you restart the computer everything should be functioning.

Please remember that if you previously were using another driver, you may need to use the livna-config-display tool to switch back to the 'AIGLX' configuration:

livna-config-display --tui -a

 

The 'fglrx' driver

To install the fglrx driver, simply run the following commands:
su -
yum install kmod-fglrx xorg-x11-drv-fglrx
fglrx-config-display enable
service fglrx restart

Please note that for a xen kernel, 'kmod-fglrx-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-fglrx-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-fglrx-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "ATI Technologies" and not "Mesa".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the ATI/AMD website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option "VideoOverlay" "On"
Q: Does fglrx 8.42.3 really work with AIGLX and Compiz?
A: From my tests, yes, although I've heard some cases may require some manual configuration.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting nVidia cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the nv, nouveau or proprietary nvidia driver with your nVidia graphics card to make sure your card is functioning as it should.

Getting nVidia cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

The 'nv' or 'nouveau' driver

The nv and nouveau drivers are the open-source alternatives to the proprietary nvidia driver, offering support for many of the nVidia cards. The downside to the nv driver is that unlike the open source 'radeon' driver for ATI cards, it does not support direct rendering, also called DRI or hardware-accelerated rendering. The nouveau project, however, aims to fix this by developing a new free driver with working DRI for nVidia cards. Currently, it is (as the name goes ;) ) a new project and it's not ready for everyday use quite yet.
 
Either way, both of these drivers are included in part of the standard Xorg driver packages in Fedora, so they requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "Name"

Where 'Name' is either 'nv' (recommended) or 'nouveau' if you're feeling lucky. Once you restart the computer everything should be functioning (or maybe not if you chose the 'nouveau' driver)

 

The 'nvidia' driver

A note on legacy drivers:

Please note that any card below the GeForce FX series is no longer supported by the mainstream nvidia drivers.

If you have a Riva or TNT card, you are going to have to use the nvidia legacy drivers. Simply follow the instructions below like normal but replace all instances of:

  • kmod-nvidia with kmod-nvidia-legacy
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-legacy
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-legacy-libs.i386
  • service nvidia [action] with service nvidia-legacy [action]

If you are using a GeForce2, 3 or 4 (including MX) card, a you are going to have to use the 96xx series. Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-96xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-96xx
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-96xx-libs.i386
  • service nvidia [action] with service nvidia-96xx [action]
Please note that the 177.82 driver dropped support for GeForce FX (5xxx) cards. Because of this, the main driver package for Fedora 9 at RPM Fusion will not be updated to 177.82. Instead, please install the newest series package to obtain the 177.82 drivers by replacing:
  • kmod-nvidia with kmod-nvidia-newest
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-newest
  • xorg-x11-drv-nvidia-libs.i386 with xorg-x11-drv-nvidia-newest-libs.i386
  • service nvidia [action] with service nvidia-newest [action]
 
To install the nvidia driver, simply run the following commands:
su -
yum install kmod-nvidia xorg-x11-drv-nvidia
nvidia-config-display enable
service nvidia restart

Please note that for a xen kernel, 'kmod-nvidia-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-nvidia-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-nvidia-libs.i386

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "NVIDIA Corporation" along with your card name and version - NOT "Mesa Indirect".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the nVidia website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option      "AddARGBGLXVisuals" "True"
Q: How come I can't use Beryl or Compiz?
A: Please take a look at your xorg.conf and remove the 'Module' section if you have it. Xorg can autoconfigure and guess at a lot of things and even run without a xorg.conf (but that's not recommended). Without a Module section, you're sure that Xorg will load all the modules you need where as with one it will only load what is specified, not more.
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting nVidia cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the nv, nouveau or proprietary nvidia driver with your nVidia graphics card to make sure your card is functioning as it should.

Getting nVidia cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

The 'nv' or 'nouveau' driver

The nv and nouveau drivers are the open-source alternatives to the proprietary nvidia driver, offering support for many of the nVidia cards. The downside to the nv driver is that unlike the open source 'radeon' driver for ATI cards, it does not support direct rendering, also called DRI or hardware-accelerated rendering. The nouveau project, however, aims to fix this by developing a new free driver with working DRI for nVidia cards. Currently, it is (as the name goes ;) ) a new project and it's not ready for everyday use quite yet.
 
Either way, both of these drivers are included in part of the standard Xorg driver packages in Fedora, so they requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "Name"

Where 'Name' is either 'nv' (recommended) or 'nouveau' if you're feeling lucky. Once you restart the computer everything should be functioning (or maybe not if you chose the 'nouveau' driver)

 

The 'nvidia' driver

A note on legacy drivers:

Please note that any card below the GeForce FX series is no longer supported by the mainstream nvidia drivers.

If you have a Riva or TNT card, you are going to have to use the nvidia legacy drivers. Simply follow the instructions below like normal but replace all instances of:

  • kmod-nvidia with kmod-nvidia-legacy
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-legacy
  • xorg-x11-drv-nvidia-libs-32bit with xorg-x11-drv-nvidia-legacy-libs-32bit
  • service nvidia [action] with service nvidia-legacy [action]

A full product support list for legacy is available here.

If you are using a GeForce2, 3 or 4 (including MX) card, a you are going to have to use the 96xx series nvidia drivers as your card is not designated as legacy but is no longer supported by the 97xx series drivers.
Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-96xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-96xx
  • xorg-x11-drv-nvidia-libs-32bit with xorg-x11-drv-nvidia-96xx-libs-32bit
  • service nvidia [action] with service nvidia-96xx [action]

A full product support list for the 96xx series driver is available here.

 
To install the nvidia driver, simply run the following commands:
su -
yum install kmod-nvidia xorg-x11-drv-nvidia
nvidia-config-display enable
service nvidia restart

Please note that for a xen kernel, 'kmod-nvidia-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-nvidia-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-nvidia-libs-32bit

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "NVIDIA Corporation" along with your card name and version - NOT "Mesa Indirect".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the nVidia website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option      "AddARGBGLXVisuals" "True"
Option "DisableGLXRootClipping" "True"
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting ATI cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the radeon or the proprietary fglrx driver with your ATI graphics card to make sure your card is functioning as it should.

Getting ATI cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

  • Yum configured to use the 3rd party Livna repository
  • If building the drivers using the packages directly from ATI/AMD's site, please install a few packages first:
    su -c 'yum install qt-devel compat-libstdc++-33 -y' 

 

The 'radeon' driver

Radeon is an open-source alternative to the proprietary fglrx driver, offering support for many (but not all) ATI cards including some that aren't supported any longer in the latest fglrx drivers! While it's performance may not match exactly that of fglrx, its performance is still very decent. It is included in part of the standard Xorg driver packages in Fedora, so it requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "radeon"

Once you restart the computer everything should be functioning.

Please remember that if you previously were using another driver, you may need to use the livna-config-display tool to switch back to the 'AIGLX' configuration:

livna-config-display --tui -a

 

The 'fglrx' driver

To install the fglrx driver, simply run the following commands:
su -
yum install kmod-fglrx xorg-x11-drv-fglrx
fglrx-config-display enable
service fglrx restart

Please note that for a xen kernel, 'kmod-fglrx-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-fglrx-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-fglrx-libs-32bit  

Common Questions

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "ATI Technologies" and not "Mesa".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the ATI/AMD website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option "VideoOverlay" "On"
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting ATI cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the radeon or the proprietary fglrx driver with your ATI graphics card to make sure your card is functioning as it should.

Getting ATI cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

  • Yum configured to use the 3rd party Livna repository
  • If building the drivers using the packages directly from ATI/AMD's site, please install a few packages first:
    su -c 'yum install qt-devel compat-libstdc++-33 -y' 

 

The 'radeon' driver

Radeon is an open-source alternative to the proprietary fglrx driver, offering support for many (but not all) ATI cards including some that aren't supported any longer in the latest fglrx drivers! While it's performance may not match exactly that of fglrx, its performance is still very decent. It is included in part of the standard Xorg driver packages in Fedora, so it requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "radeon"

Once you restart the computer everything should be functioning.

Please remember that if you previously were using another driver, you may need to use the livna-config-display tool to switch back to the 'AIGLX' configuration:

livna-config-display --tui -a

 

The 'fglrx' driver

To install the fglrx driver, simply run the following commands:
su -
yum install kmod-fglrx xorg-x11-drv-fglrx
fglrx-config-display enable
service fglrx restart

Please note that for a xen kernel, 'kmod-fglrx-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-fglrx-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-fglrx-libs-32bit  

Common Questions

Q: What does transaction error with conflicting files mean?
A: If you're seeing lots of messages like this when trying to install or upgrade the fglrx driver:

Transaction Check Error: package kernel-2.6.19-1.2911.6.5.fc6 is already installed

file /boot/System.map-2.6.19-1.2911.6.5.fc6 from nstall of kernel-2.6.19-1.2911.6.5.fc6
conflicts with file from package kernel-2.6.19-1.2911.6.5.fc6

file /boot/config-2.6.19-1.2911.6.5.fc6 from install of kernel-2.6.19-1.2911.6.5.fc6
conflicts with file from package kernel-2.6.19-1.2911.6.5.fc6
[...]

it means you have been hit by the Anaconda i586/i686 bug. Please see this page for instructions on solving the issue.

 

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "ATI Technologies" and not "Mesa".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the ATI/AMD website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option "VideoOverlay" "On"
 
Need more help or want to ask a question? Discuss this topic here.
Rating: 

Getting nVidia cards to work in Fedora

Ensuring that your graphic card works the way you want it to in Linux can be a long and tenious task if you are encountering problems. This guide will show you how to setup the nv, nouveau or proprietary nvidia driver with your nVidia graphics card to make sure your card is functioning as it should.

Getting nVidia cards to work

Need more help or want to ask a question? Discuss this topic here.
 

Requirements

The 'nv' or 'nouveau' driver

The nv and nouveau drivers are the open-source alternatives to the proprietary nvidia driver, offering support for many of the nVidia cards. The downside to the nv driver is that unlike the open source 'radeon' driver for ATI cards, it does not support direct rendering, also called DRI or hardware-accelerated rendering. The nouveau project, however, aims to fix this by developing a new free driver with working DRI for nVidia cards. Currently, it is (as the name goes ;) ) a new project and it's not ready for everyday use quite yet.
 
Either way, both of these drivers are included in part of the standard Xorg driver packages in Fedora, so they requires almost no configuration at all! Simply edit the /etc/X11/xorg.conf file and in the "Device" section you will come across a line like this:
Driver "DriverNameHere"

 Change this line to:

Driver "Name"

Where 'Name' is either 'nv' (recommended) or 'nouveau' if you're feeling lucky. Once you restart the computer everything should be functioning (or maybe not if you chose the 'nouveau' driver)

 

The 'nvidia' driver

A note on legacy drivers:

Please note that any card below the GeForce FX series is no longer supported by the mainstream nvidia drivers.

If you have a Riva or TNT card, you are going to have to use the nvidia legacy drivers. Simply follow the instructions below like normal but replace all instances of:

  • kmod-nvidia with kmod-nvidia-legacy
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-legacy
  • xorg-x11-drv-nvidia-libs-32bit with xorg-x11-drv-nvidia-legacy-libs-32bit
  • service nvidia [action] with service nvidia-legacy [action]

A full product support list for legacy is available here.

If you are using a GeForce2, 3 or 4 (including MX) card, a you are going to have to use the 96xx series nvidia drivers as your card is not designated as legacy but is no longer supported by the 97xx series drivers.
Simply follow the instructions like normal but replace:

  • kmod-nvidia with kmod-nvidia-96xx
  • xorg-x11-drv-nvidia with xorg-x11-drv-nvidia-96xx
  • xorg-x11-drv-nvidia-libs-32bit with xorg-x11-drv-nvidia-96xx-libs-32bit
  • service nvidia [action] with service nvidia-96xx [action]

A full product support list for the 96xx series driver is available here.

 
To install the nvidia driver, simply run the following commands:
su -
yum install kmod-nvidia xorg-x11-drv-nvidia
nvidia-config-display enable
service nvidia restart

Please note that for a xen kernel, 'kmod-nvidia-xen' will need to be installed. This rule is applied to all the kernel variants, such as PAE (kmod-nvidia-PAE) and so on. 

Additionally, if you are running a x86_64 (a 64-bit) operating system the 32bit libraries can be installed for compatibility reasons:

yum install -y xorg-x11-drv-nvidia-libs-32bit

Common Questions

Q: What does transaction error with conflicting files mean?
A: If you're seeing lots of messages like this when trying to install or upgrade the nvidia driver:

Transaction Check Error: package kernel-2.6.19-1.2911.6.5.fc6 is already installed

file /boot/System.map-2.6.19-1.2911.6.5.fc6 from nstall of kernel-2.6.19-1.2911.6.5.fc6
conflicts with file from package kernel-2.6.19-1.2911.6.5.fc6

file /boot/config-2.6.19-1.2911.6.5.fc6 from install of kernel-2.6.19-1.2911.6.5.fc6
conflicts with file from package kernel-2.6.19-1.2911.6.5.fc6
[...]

it means you have been hit by the Anaconda i586/i686 bug. Please see this page for instructions on solving the issue.

 

Q: How can I test if the driver works now that it's installed?

A: Simply run 'glxgears' like this:

glxgears 

Alternatively you can also check the output of 'glxinfo':

glxinfo | grep direct -i
glxinfo | grep OpenGL -i
It should return "direct rendering: yes" and also various OpenGL information concerning "NVIDIA Corporation" along with your card name and version - NOT "Mesa Indirect".
 
Q: Help! I followed the instructions and DRI still isn't working!
A: If you're using the drivers from the nVidia website or if you've previously installed them, please see this post on the RedHat mailinglists as to why it could be a problem. In short, those drivers tend to overwrite other system files which can cause problems, where as the packaged drivers from Livna or other third party repositories do not. If you think this is your problem, pease reinstall all Mesa GL and Xorg server packages to restore the replaced system files.
Q: What if it still doesn't work?
A: If you are not using the Livna drivers, then your xorg.conf may not be automatically edited for you. You may need to add this option to your /etc/X11/xorg.conf under the "Device" section:
Option      "AddARGBGLXVisuals" "True"
Option "DisableGLXRootClipping" "True"
 
Need more help or want to ask a question? Discuss this topic here.
Rating: